SmartSeal WB™

Add life and longevity to your (stained) concrete with SmartSeal WB, a nano-acrylic, top coat sealer for general use. The water-based formula is used to protect SmartColor™ and other NewLook stains, properly prepared concrete floors, pool decks and other concrete and masonry surfaces.

SmartSeal WB dries quickly and, once cured, creates an abrasion-resistant film that provides weatherproof protection against sun, rain, most acids, industrial chemicals, oil and grease. SmartSeal WB complies with all environmental regulations (VOC < 100 g/L). 

NOTE: SmartColor and other NewLook stains may be installed over cured SmartSeal WB. Apply SmartSeal WB with NewLook's slip-resistant grit for greater traction.

Features & Benefits:
  • Water-based, nano-acrylic
  • Good exterior & interior surface protection
  • Excellent blush & early water resistance
  • May be applied to damp concrete surfaces
  • Good hot-tire pickup resistance
  • Early block resistance; reduces dirt pickup
  • Non-yellowing
  • Water-based, eco-friendly solution
  • UV-resistant; strong UV-blockers
  • Resistant to water, chemicals and abrasion

Applications:
  • Light-to-moderate traffic concrete & masonry
  • Interior and exterior concrete floors
  • Residential and commerical
  • Garage floors
  • Kitchen and basements
  • Concrete driveway sealer
  • Stamped concrete sealer

Finish: Matte, Satin or Gloss

Packaging: 1, 5 and 55 gallon containers

Coverage: Approximately 300 - 500 square feet (27.9 - 46.5 square meters) per gallon.

Downloads:

Products  |  Gallery  |  Training  |  Blog  |  Color Chart  |  Find Suppliers
© 2011 NewLook International, Inc. All Rights Reserved

Tell a friend about this page
SmartSeal product image
Follow Us:
SmartSeal gray sealed concrete
SmartSeal™
    It's Liquid Awesome!
SmartSeal AU™

Available versions:
  • SmartSeal AU-34 (34% Solids)
  • SmartSeal AU-25 (25% Solids)

Protect your high-traffic concrete with NewLook's innovative SmartSeal AU, a very durable nano-acrylic urethane top coat sealer for surfaces subject to heavier wear and tear.

SmartSeal AU dries quickly and, once cured, creates a very abrasion-resistant film that provides weatherproof protection against sun, rain, most acids, industrial chemicals, oil and grease. SmartSeal AU complies with all environmental regulations (VOC < 100 g/L).

SmartSeal AU may be used for both interior and exterior concrete floors. However, NewLook recommends using sealers with lower solids content outdoors where breathability is more critical. Apply SmartSeal AU with NewLook's slip-resistant grit for greater traction.

Features & Benefits:
  • Water-based, nano-acrylic urethane
  • Very Good exterior & interior protection
  • Excellent blush & early water resistance
  • May be applied to damp concrete surfaces
  • Very strong hot-tire pickup resistance
  • Early block resistance; reduces dirt pickup
  • Non-yellowing
  • Water-based, eco-friendly solution
  • UV-resistant; strong UV-blockers
  • Reistant to water, chemicals and abrasion

Applications:
  • High-traffic concrete & masonry
  • Interior and exterior concrete floors
  • Residential and commerical
  • Retail and restaurant concrete flooring
  • Industrial garages & warehouse floors
  • Kitchen and basements

Finish: Satin or Gloss

Packaging: 1, 5 and 55 gallon containers

Coverage: Approximately 300 - 500 square feet (27.9 - 46.5 square meters) per gallon.

Downloads:
Additional Information

SmartSeal WB is the best general purpose concrete sealer; it resists light to moderate traffic and protects your stained concrete floor from damage. Use SmartSeal WB as a concrete driveway sealer, stamped concrete sealer, among other applications.

MIXING & APPLICATION INSTRUCTIONS

1. Stir thoroughly before using. Do not dilute.
2. Apply thin, even coats using a brush, roller, microfiber pad, or sprayer. Do not exceed 1 – 2 mils in thickness. If puddles occur, immediately brush or roll out.
3. Apply coating only when air and surface temperature are between 50°F (10°C) rising and 90°F (32°C) and cooling.
4. Mix NewLook Slip-Resistant Grit™ with concrete sealant to increase traction.
5. SmartSeal dries to a clear finish with early water/blush resistance. Recommend two thin coats for optimal protection.

CURING AND POST APPLICATION

Complete drying times will vary depending on concrete temperature, air temperature, humidity, concrete porosity, and other local conditions. At 77°F (25°C) and 50% relative humidity:
  • Dry to the touch: 15 to 20 minutes.
  • Completely Dry: 50 to 60 minutes.
  • Initial cure time: 8 to 12 hours.
  • Full cure time: 7 – 14 days.
  • Note: Lower temperatures and/or higher humidity will increase cure time.
  • Maintain dry during cure time. 
  • Keep foot traffic off for 4 to 8 hours.
  • Wait up to 48 hours before driving or parking vehicles.

CONCRETE SEALER MAINTENANCE

  • Regular cleaning with NewLook Concrete Cleaner is recommended. Lightly scrub the soiled area with a window washing brush or mop. Rinse thoroughly with clean water and allow the area to dry.
  • The sealed concrete surface should be inspected periodically for thin or trafficworn areas. Re-apply concrete sealer as needed with a maintenance application.
  • It is common practice to apply a wax finish over SmartSeal WB to increase the protection and longevity of the concrete surface.
  • Apply additional coatings of SmartSeal WB as needed. Re-apply concrete sealer after maintenance installations of NewLook's decorative concrete stain.